MicroMax's Solutions
MicroMax's Solutions
MicroMax's Solutions
BAT104-NiCd
PC104 NiCd Battery Backup Module
The BAT104-NiCd creates a complete UPS system by plugging directly into the bottom of the HESC (including the V5SC-SER) Vehicle Power Supplies. The BAT104-NiCd includes seven 600ma-hr NiCd batteries for a total of 5 watt-hours of power. Therefore a BAT104-NiCd can supply backup power for up to sixty minutes to a 5 watt load.
The BAT104-NiCd includes Mosfet transistors for preventing deep discharge occurrences during extended power outages. The Mosfet transistors electrically isolate the BAT104-NiCd from the HESC whenever the BE output of the HESC is de-asserted (pulled to 5V).
The BAT104-NiCd has both a thermal fuse and a current fuse for protection against overcharging, and shorts on the battery output.
A digital I2C temperature sensor provides temperature feedback for charge termination, which can be read by the HESC.
HPSC104-SER
160 Watt UPS High Power PC/104 Vehicle Power Supply with Smart Charging
The HPSC104-SER is a DC-DC converter that includes a flash based microcontroller and 4 amp charger for advanced power management and smart battery charging. Combined with a Tri-M standard battery pack or super cap module, the HPSC104-SER can be used as an Uninterruptible Power Source (UPS) for a PC/104 system. The HPSC104-SER is designed for low noise embedded computer systems, has a wide input range of 6 to 40 V DC and is ideal for battery or unregulated input applications.
The HPSC104-SER provides up to four stages of battery charging and can charge SLA, NiCd, and NiMh batteries and level two and three SMBus compatible batteries. Charge currents are up to 4A, and battery charging voltages from 10V to 35V DC.
The HPSC104-SER has advanced power management functions that allows timed on/off control of the unit, notification of changes to main power and changes in the battery status. For example, the HPSC104-SER can be programmed to power off the main outputs in 60 seconds and then turn them on again 12 hours later. In addition to smart charging and power management the HPSC104-SER can monitor up to 16 different temperatures using digital I²C digital temp sensors. The HPSC104-SER is available as RoHS, is PC/104 compliant and rugged enough for to meet the demands on military and mining vehicle power supplies, including -40°C to +85°C extended temperature rating.
HPS3512
203W Smart PC104 PSU
The HPS3512 is a high power, high performance PC104 PSU that supplies +3.3V, +5V, and +12V outputs. The HPS3512 also includes a flash based microcontroller that supplies advanced power management, and an RS232 serial port. The HPS3512 is designed for low noise embedded computer systems, has a wide input range of 6-40V (>6:1) and is ideal for battery or unregulated input applications. The HPS3512 is specifically designed for vehicular applications and has heavy-duty transient suppressors (up to 18000W) that clamp the input voltage to safe levels, while maintaining normal power supply operation.
The HPS3512 is a state-of-the-art Mosfet based design that provides outstanding line and load regulation with efficiencies up to 90 percent. Organic Semiconductor Capacitors (OSC-CON) and Polymerized Organic Semiconductor capacitors (POSCAP) provide filtering that reduces ripple noises below 20mV. The low noise design makes the HPS3512 ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized. Constant frequency architecture controllers provide excellent line and load transient response on the +5VDC and +12VDC outputs.
The HPS3512 has advanced power supply management functions that allows timed on/off control of the HPS3512, notification of changes to main power and secondary power status. For example, the HPS3512 can be programmed to power off the outputs in 60 seconds, and then turn on again 12 hours later.
The HPS3512 size is 3.55×3.775 inches, which is the same size as the PC/104 standard, and has the same mounting holes pattern as the PC/104 standard. However, the HPS3512 does not include the PC/104 bus connectors. All generated voltages are provided to a removable header. A removable plug allows the HPS3512 to be easily installed. The RS232 serial port is provided on a 2×5 row pin header.
The HPS3512 can be configured to meet almost any power supply and battery powered need for embedded applications, whether that is a simple +5V application, or providing power for backlighted LCD panels.
HE-HP
100W PC104 PSU Module
The HE-HP is a high efficiency, high performance DC to DC 100 watt power supply module that supplies +5V and +12V outputs. The HE-HP is designed for low noise embedded computer systems, has a wide input range of 6-40V (>6:1) and is ideal for battery or unregulated input applications. The HE-HP is specifically designed for vehicle power supply applications and has four heavy-duty transient suppressors (providing 6000W of protection) that clamp the input voltage to safe levels, while maintaining normal power supply operation.
The HE-HP is a state-of-the-art Mosfet based design that provides outstanding line and load regulation with efficiencies up to 90 percent. Organic Semiconductor Capacitors provide filtering that reduces ripple noises below 20mV. The low noise design makes the HE-HP ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized. The +5VDC and +12VDC outputs are controlled by a constant off-time current-mode architecture regulator that provides excellent line and load transient response.
The HE-HP has an opto-isolated on/off input (SD), allowing for remote control.
The HE-HP has a PC/104 footprint with PC/104 mounting holes. All generated voltages are provided to a connector block.
HESC-SERD
60W Smart Embedded Power Supply
The HESC-SERD is a high efficiency, high performance DC to DC 60 watt embedded power supply that supplies +5V, −5V, +12V & −12V outputs. The HESC-SERD also includes a flash based microcontroller that supplies advanced power management, smart battery charger and an RS232 serial port. The HESC-SERD is designed for low noise embedded computer systems, has a wide input range of 6-50V (>8:1) and is ideal for battery or unregulated input applications. The HESC-SERD is specifically designed for vehicular applications and has heavy-duty transient suppressors (9000W) that clamp the main input voltage to safe levels, while maintaining normal power supply operation.
The HESC-SERD is a state-of-the-art Mosfet based design that provides outstanding line and load regulation with efficiencies up to 95 percent. Organic Semiconductor Capacitors provide filtering that reduces ripple noises below 20mV. The low noise design makes the HESC-SERD ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized. The +5VDC and +12VDC outputs are controlled by a constant off-time current-mode architecture regulator that provides excellent line and load transient response.
The HESC-SERD provides up to four stages of battery charging and can charge Lead-Acid, NiCd, and NiMh batteries and is also SMBus level 3 compatible. Charge currents are up to 4A, and battery charging voltages from 9.5 to 35V.
The HESC-SERD has advanced power management functions that allows timed on/off control of the HESC-SERD, notification of changes to main power and changes in the battery status. For example, the HESC-SERD can be programmed to power off the outputs in 60 seconds, and then turn on again 12 hours later.
The HESC-SERD size is 3.55×3.75 inches, which is the same size as the PC/104 standard, and has the same mounting holes pattern as the PC/104 standard. However, the HESC-SERD does not supply the PC/104 bus connectors. (For a fully compliant PC/104 embedded power supply, please see Tri-M’s HESC104.) All generated voltages are provided to a removable pluggable header. The removable plug allows the HESC-SERD to be easily installed. The RS232 serial port is provided on a 2×5 row pin header.
The HESC-SERD can be configured to meet almost any power supply and battery charging need for embedded applications, whether that be a simple +5V application, or providing power for back lighted LCD panels, or a full UPS (un-interruptible power supply configuration).
HE104
60W Rugged PC/104 Power Supply
The HE104 is a high efficiency, high performance DC to DC 60 watt converter that supplies 5V, 12V, −12V (optional), −5V (optional) outputs. The HE104 is specifically designed for vehicular applications requiring low noise, has an ultrawide input range of 6-40V and is ideal for battery and unregulated input applications.
The input protection circuit includes an input filter, three heavy duty transient suppressors (5000W), Mosfet reverse polarity protection and an active circuit surge stopper with Mosfet.
The HE104 5V output is a synchronous buck regulator design that provides outstanding line and load regulation and ripple noise below 20mV. The low noise design makes the HE104 ideal for use on aircraft and military applications or wherever EMI or RFI must be minimized.
The HE104 12V output is a synchronous boost regulator that converts the 5V rail up to 12V. This allows the main input to range from a low of 6V up to 40V while maintaining both 5V and 12V output within their specified levels.
The HE104 has a opto-isolated on/off input (SD), allowing for remote signal between 6 and 40V to control the On/Off operation of the outputs. When jumper shunt JP2 is intalled (default) the outputs will automatically turn on when main power is applied to CN1.
The HE104 is PC/104 compliant with a 16-bit PC/104 bus. All generated voltages are provided to the auxilliary power connector block CN2. A removable main input power plug allows the HE104 to be easily installed.
HESC104+
108W Smart Charging PCI-104 Power Supply
The HESC104+ is a high efficiency, high performance PCI-104 DC-to-DC converter that supplies +3.3V, +5V, +12V & −12V outputs. The HESC104+ also includes a flash based microcontroller that supplies advanced power management, smart battery charger and the PCI-104 bus (also known as the Plus connector on the PC/104+ format). The HESC104+ is designed for low noise embedded computer systems, has a wide input range of 6-40V (>6:1) and is ideal for battery or unregulated input applications. The HESC104+ is specifically designed for vehicular applications and has heavy-duty transient suppressors (9000W on both main and secondary inputs) that clamp the input voltage to safe levels, while maintaining normal power supply operation.
The HESC104+ is a state-of-the-art Mosfet based design that provides outstanding line and load regulation with efficiencies up to 95 percent. Organic Semiconductor capacitors provide filtering that reduces ripple noises below 20mV. The low noise design makes the HESC104+ ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized. The +5VDC and +12VDC outputs are controlled by a constant frequency architecture regulator that provides excellent line and load transient response.
The HESC104+ provides up to four stages of battery charging and can charge Lead-Acid, NiCd, and NiMh batteries and level two and level three SMBus compatible batteries. Charge currents are up to 4A, and battery charging voltages from 9.5 to 19.5V.
The HESC104+ has advanced power management functions that allows timed on/off control of the HESC104+, notification of changes to main power and changes in the battery status. For example, the HESC104+ can be programmed to power off the main outputs in 60 seconds and then turn them on again 12 hours later.
The HESC104+ can be configured to meet almost any power supply and battery charging need for embedded applications, whether that be a simple +5V application, or providing power for back lighted LCD panels, or a full UPS (uninterruptible power supply configuration).
HESC104
60W Smart Charging PC104 Power Supply
The HESC104 is a 60W DC-DC PC104 Power Supply that includes a flash based microcontroller and 4 amp charger for advanced power management and smart battery charging. Combined with a Tri-M standard battery pack or super cap module, the HESC104 can be used as an Uninterruptible Power Source (UPS) for a PC104 system.
The HESC104 is designed for low noise embedded computer systems, has a wide input range of 6-40V (>6:1) and is ideal for battery or unregulated input applications. The HESC104 is specifically designed for the rugged demands of vehicular applications and has heavy-duty transient suppressors (5000W) that clamp the input voltage to safe levels, while maintaining normal power supply operation.
The +/-5V DC and +/-12V DC outputs are controlled by a constant off-time current-mode architecture regulator that provides excellent line and load transient response.
The HESC104 provides up to four stages of battery charging and can charge SLA, NiCd, and NiMh batteries and level two and three SMBus compatible batteries. Charge currents are up to 4A, and battery charging voltages from 9.5 to 19.5V.
The HESC104 has advanced power management functions that allows timed on/off control of the HESC104, notification of changes to main power and changes in the battery status. For example, the HESC104 can be programmed to power off the main outputs in 60 seconds and then turn them on again 12 hours later.
In addition to smart charging and power supply management the HESC104 can monitor up to 16 different temperatures using digital I²C digital temp sensors. The HESC104 is available as RoHS, is PC/104 compliant and −40°C to +85°C is standard.
HE104-75W
75 Watt High Efficiency PC104 Power Supply
For applications requiring a DC-DC PC104 power converter that supplies up to 75W of power, Tri-M offers the HE104‑75W. It is ideal for use on 12VDC and 24VDC mobile applications where power from a DC source (input) needs to be converted (output) to match the applications power requirements - generally an embedded computer.
Efficiency of the HE is over 90% - the higher efficiency means less heat is generated - and it is designed to operate in extended temperature applications where temperatures can be between -40°C and +85°C.
Input voltage spikes that go beyond the input voltage window (9VDC to 40VDC) are managed through transient suppressors that restrict the input voltage, while maintaining normal output power operation.
The HE104-75W is designed to minimize any generated noise or interference, allowing it to be used for airborne or ground vehicles that encounter EMI or RFI.
HE104+DX
108W PC104-Plus Power Supply
The HE104+DX is designed for low noise embedded computer systems, has a wide input range of 6-40V (>6:1) and is ideal for battery or unregulated input applications. The HE104+DX is specifically designed for vehicular applications and has heavy-duty transient suppressors (9000W on both main and secondary inputs) that clamp the input voltage to safe levels, while maintaining normal power supply operation.
The HE104+DX is an embedded power supply with state-of-the-art Mosfet based design that provides outstanding line and load regulation with efficiencies up to 90 percent. Organic Semiconductor Capacitors provide filtering that reduces ripple noises below 20mV. The low noise design makes the HE104+DX ideal for use aboard aircraft or military applications or wherever EMI or RFI must be minimized. The +5VDC and +12VDC outputs are controlled by a constant frequency architecture regulator that provides excellent line and load transient response.
The HE104+DX has an optocoupled on/off input (SD) to control the outputs of the HE104+DX. To enable the HE104+DX outputs, a 6 to 40V signal must be connected to the SD input. If remote control is not required, the SD input can be connected to the main power input. The common for the remote 6 to 40V signal must be connected to the HE104+DX common. If the SD input is connected directly to the main input power connector, the common for the SD input is already done. The HE104+DX is now RoHS compliant.
