PCAN-USB FD
PCAN-USB FD CAN and CAN FD Interface for High-Speed USB 2.0 The CAN FD adapter PCAN-USB FD allows the connection of CAN FD and CAN networks to a computer via USB. A galvanic isolation of up to 500 Volts decouples the PC from the CAN bus. The simple handling and its compact plastic casing make the adapter suitable for mobile applications. The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable. The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD. ISO / Non-ISO CAN FD: Since the first implementations of CAN FD, the protocol has been improved and is now included in the standard ISO 11898-1. The revised CAN FD standard is not compatible with the original protocol. PEAK-System takes this into account by supporting both protocol versions with their CAN FD interfaces. If required, the user can switch to the CAN FD protocol used in the environment by software (Non-ISO and ISO).
MZ-6SER
MZ-6SER PC/104 bus compatible ZFx86 SBC with six serial ports The MZ-6SER is an embedded system controller measuring just 3.63 inches x 4.86 inches, which incorporates the revolutionary ZFx86 “PC-on-a-chip” processor. The MZ-6SER offers the quickest route of integrating a full x86 AT-compatible computer into your embedded control application. In addition, the built-in peripherals minimize the number of additional modules required. By combining the system hardware, I/O, software, and solid-state mass storage, the MZ-6SER lowers your exposure to possible development risks, costs and significantly reduces your time-to-market. The MZ-6SER’s fully compatible PC/104 embedded expansion bus, permits easy integration to a wide selection of low-cost hardware peripherals. The numerous features provide an ideal price/performance solution.
MZ104
MZ104 100Mhz PC/104 Module The MZ104 is a PC/104 compliant system controller measuring just 3.55 inches by 3.775 inches. The MZ104 offers the quickest route of integrating a full x86 AT-compatible computer into your embedded control application using the PC/104 form factor. In addition, the built-in peripherals minimize the number of additional modules required. By combining the system hardware, I/O, software (integrated RTOS image) and solid-state mass storage, the MZ104 lowers your exposure to possible development risks, costs and significantly reduces your time-to-market. The MZ104’s full compatibility with the popular PC/104 embedded expansion bus, which allows you to easily integrate the widest selection of low-cost hardware peripherals. The numerous features provide an ideal price/performance solution.
ETX-GX2
ETX-GX2 ETX module ETX-GX2 is an RoHS compliant ETX module specially designed to facilitate speedy development of semi custom designs. The ETX-GX2 core consists of an AMD Geode GX2 processor and AMD Geode CS5535 companion device. The GX2 CPU onboard is available in two version : as a Geode GX533@1.1W or as a Geode GX466@0.9W The ETX-GX2 supports DDR based SODIMMs. Memory can be soldered on board as either 128MB or 256MB, and/or can be inserted in the onboard 200-pin SODIMM socket that accept up to 512 MB DDR SODIMMs. The ETX-GX2 incorporates a VGA controller, an single channel EIDE controller supporting both PIO and UDMA modes, 4 USB ports, two serial ports, one parallel port (SPP/ECP/EPP) shared with FDD, one PS2 keyboard/mouse interface. Additionally onboard are an 10/100Base-T Ethernet port, watchdog timer, an AC97 Audio Codec and support for LVDS based Flat Panel displays.
Diamond-MM-32-AT
Diamond-MM-32-AT 16-bit Analog I/O PC/104 Module With Autocalibration After reading about our new Diamond-MM-32 board, we think you will be convinced: There is simply no other board in the world that can compare with these features at any price. And that does not mean that this board is expensive. On the contrary, we have priced Diamond-MM-32 to compete with the standard 16-bit A/D boards that you will find from our competitors around the world. Take a look at the performance and features described below and see for yourself. Diamond-MM-32 is the first PC/104 analog I/O board to feature automatic calibration of both analog inputs and outputs for enhanced accuracy and reliability. The potentiometers, which are subject to tampering and vibration, have been eliminated. Instead, all A/D calibration adjustments are performed using an octal 8-bit DAC. The DAC values are stored in an EEPROM and are recalled automatically on power up. The board includes three precision voltage references for negative full scale, zero, and positive full-scale. A calibration utility program provided with the board allows you to recalibrate the board anytime, in both unipolar and bipolar modes, and store the new settings in EEPROM. Autocalibration applies to the 4 D/A channels as well. The full-scale D/A range is selected with a jumper block. The analog outputs are fed back to the A/D converter so they can be calibrated without user intervention. Again, calibration settings are stored in EEPROM and automatically recalled on power-up.
Diamond-MM-48-AT
Diamond-MM-48-AT Autocalibrating 16-ch 16-bit A/D + 8-ch 12-bit D/A Ext Temp Diamond-MM-48-AT is the newest in Diamond Systems’ popular AT series of PC/104 autocalibrating analog I/O boards. It combines the features of two different I/O boards into a single board to reduce the size and weight of your PC/104 stack: The analog I/O features are similar to our DMM-16-AT board: 16 analog inputs with 16-bit A/D, 8 analog outputs with 12-bit D/A, and on-board counter/timer for A/D sample rate and interrupt control. The digital I/O features are similar to our Opal-MM board: 8 relays with SPDT (form C) contacts and 4 optocouplers with up to 28V AC/DC input capability. The optocouplers feature an interrupt on edge detection feature for safety applications. An additional 4 TTL level digital I/O lines are also provided on the board, and these lines also feature interrupt on edge detection capability. Diamond-MM-48-AT is designed for rugged environments. It uses latching I/O connectors, and all jumpers can be bypassed with the installation of 0-ohm resistors to provide a vibration-proof fixed configuration. In addition the board is tested and guaranteed to operate reliably over the industrial temperature range of -40 to +85oC.
Show:
Login / Registration
укажите почту
введите пароль
Forgot password?
By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy
Loading data...
Subscribe to our newsletter
specify your contacts

By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy

You have successfully subscribed
Now you can receive newsletters