Sections All products
Use checkboxes for multiple choice, click a name to enter one section only.
Updating results...
Form Factors All form-factors
Use checkboxes for multiple choice, click a name to enter one section only.
  • Select all / Select none

Updating results...
Vendor All vendors
Use checkboxes for multiple choice, click a name to enter one section only.
  • Select all / Select none

Updating results...
FP-DAQ1616 FP-DAQ1616 FeaturePak Analog I/O Data Acquisition Module with 2MHz A/D, D/A, autocalibration, and digital I/O FP-DAQ1616is adata acquisition I/O card integrating Diamond’s newest and fastest analog I/O technology and aPCI Express host interface. This tiny board offers 16-bit or12-bit A/D sampling atupto2MHz, supported with anexpanded 16K-sample FIFO for reliable data collection inany operating system. Analog output capability has been expanded to16 16-bit channels with programmable output ranges. All analog I/O features are enhanced with our industry-leading autocalibration technology, featuring independent calibration factors for each input and output range toguarantee maximum accuracy across all operating modes and the entire operating temperature range. Digital I/O features include seven 8-bit ports with both bit-wide and byte-wide direction control, two 32-bit up/down counter/timers with programmable input source and gate, and four 24-bit pulse-width modulation circuits with 0-100% duty cycle. P104-DAQ1616 P104-DAQ1616 PC/104-Plus Analog I/O Data Acquisition Module with 2MHz A/D, D/A, autocalibration, and digital I/O P104-DAQ1616is aPC/104-Plus data acquisition I/O card integrating Diamond’s newest and fastest analog I/O technology and aPCI Express interface. This module offers 16-bit or12-bit A/D sampling atamaximum of2MHz, supported with anexpanded 16K-sample FIFO for reliable data collection inany operating system. Analog output capability has been expanded to16 16-bit channels with programmable output ranges. All analog I/O features are enhanced with our industry-leading autocalibration technology, featuring independent calibration factors for each input and output range toguarantee maximum accuracy across all operating modes and the entire operating temperature range. Digital I/O features include seven 8-bit ports with both bit-wide and byte-wide direction control, two 32-bit up/down counter/timers with programmable input source and gate, and four 24-bit pulse-width modulation circuits with 0-100% duty cycle.
Diamond-MM-16R-AT Diamond-MM-16R-AT PC/104 16-Bit Analog I/O Module with Autocalibration The DMM-16R-AT features top performance and flexibility for amid-range price. Ithas 16single-ended/ 8differential analog voltage inputs with both unipolar and bipolar input ranges, programmable gain, and amaximum sampling rate of100KHz. The 4D/A channels and 16digital I/O lines provide additional real-world control and monitoring capability. The full −40 to+85°C industrial temperature operation ensures reliable and accurate performance inany embedded system application. Afully-featured software library with example programs and agraphical user interface completes the solution tomake the DMM-16R-AT asolid choice for PC/104 embedded systems requiring analog I/O. DMM-16R-AT isfully compatible with the original DMM-16-AT analog I/O module and can serve asadrop-in replacement offering reduced cost and enhanced digital I/O features. The mechanical design, connector type and pinout, and software interface are all identical the original board, eliminating any mechanical orsoftware engineering efforts. DIAMOND-MM-16RP-AT DIAMOND-MM-16RP-AT PC/104 16-Bit Analog I/O Module with Autocalibration The DMM-16RP-AT features top performance and flexibility for amid-range price. Ithas 16single-ended/ 8differential analog voltage inputs with both unipolar and bipolar input ranges, programmable gain, and amaximum sampling rate of100KHz. The 4D/A channels and 16digital I/O lines provide additional real-world control and monitoring capability. The full −40 to+85°C industrial temperature operation ensures reliable and accurate performance inany embedded system application. Afully-featured software library with example programs and agraphical user interface completes the solution tomake the DMM-16RP-AT asolid choice for PC/104-Plus embedded systems requiring analog I/O. DMM-16RP-AT isimplemented asaPC/104-Plus board, however itfeatures anovel dual bus interface. Both ISA and PCI connectors are installed and connected tothe FPGA. The board will autoselect the PCI bus when present, however ajumper can beused todisable the PCI bus and force the board into ISA bus mode ifdesired. This allows the board tobeused inboth PCI and ISA bus PC/104 systems (assuming the PCI-104 connector does not pose amechanical interference problem with other boards inthe system). The board uses 3.3V signaling onthe PCI bus and must beused only with 3.3VPCI bus SBCs. The ISA bus uses the standard 5Vlogic levels.
Onyx-MM-DIO Onyx-MM-DIO Low-Cost 48-Line Digital I/O PC/104 Module If you are looking for a basic 48-line digital I/O PC/104 module, then Onyx-MM-DIO is what you need. This module is the same as our Onyx-MM digital & counter/timer module but without the counter/timer and interrupt circuitry. This board still has the quality and attention to detail of our other modules, such as: 10K Ohm pull-up resistors on all I/O lines; all ports reset to 0 on power-up or system reset; connector pinouts compatible with our other digital I/O boards; and free software. The 48 digital I/O lines on Onyx-MM-DIO are based on 2 82C55 ICs. They can be programmed for input or output in groups of 8 lines. Direct as well as strobed (latched) I/O modes are supported, and all I/O lines are connected to 10K Ohm pull-up resistors. Onyx-MM Onyx-MM Programmable Counter/Timer, Interrupt, and Digital I/O PC/104 Module Extensive software control of features is the highlight of this digital I/O module featuring 48 digital I/O lines, 3 16-bit counter/timers, and 3 independent PC bus interrupt inputs. The 48 digital I/O lines on Onyx-MM are based on 2 82C55 ICs. They can be programmed for input or output in groups of 8 lines. Direct as well as strobed (latched) I/O modes are supported, and all I/O lines are connected to 10K Ohm pull-up resistors. The 3 16-bit counter/timers are based on an 82C54 IC. They are controlled through a configuration register on Onyx-MM (in addition to the standard 82C54 configuration register). The counter inputs can be switched between external signals, the on-board 4MHz clock oscillator, or counter outputs, all under software control. By using one counters output as another counters input, you can cascade counters in software to create a 32-bit or 48-bit counter. Onyx-MM also features programmable interrupt operations. A second software-controlled register on board configures up to 3 interrupt lines on the PC bus. Interrupts can be generated by the counter/timer outputs, digital I/O lines, or an external input line. This allows you to use a counter to generate bus interrupts at a programmed periodic rate, generate hardware interrupts under software control, or generate interrupts in response to an external event.
GPIO-MM GPIO-MM Reconfigurable 48-line Digital I/O + Counter/Timer PC/104 Module GPIO-MM is part of a family of reconfigurable digital I/O and counter / timer modules with various port and pin configurations. Each board uses identical hardware with a 200K gate Xilinx Spartan II RAM-based FPGA. The varying configurations are based on different FPGA code. The FPGA code is stored in a flash memory on the board, enabling GPIO-MM to be reprogrammed in the field with different designs, including custom designs. The GPIO-MM configuration provides 48 digital I/O lines and 10 programmable counter/timers. The counter/timer features are based on our legacy Quartz-MM board, while the 48 digital I/O lines are compatible with our legacy Garnet-MM board. This configuration combines the features of both these boards into one board to reduce your PC/104 stack size and cost. Other GPIO-MM configurations provide up to 96 digital I/O lines. IR104 IR104 Industrial Relay Board Initially developed for industrial applications, the rugged IR-104 was conceived in the PC/104 format as a high-density I/O module for applications requiring isolation between the computer and its external switches. This versatile module features 20 optoisolated digital inputs boasting a 3V to 24V range AC or DC. The 20 relay outputs are housed on an easily detachable connector with a rating of 5A @ 250V AC and 30V DC. This lightweight board features a compact 3.550” x 3.775” footprint while exceeding industry standards with a 0.492” maximum component height. With an impressive operating temperature range of –25 to +70 degrees Fahrenheit, this versatile relay board is easily adapted to any number of unique applications.
Show:
Login / Registration
укажите почту
введите пароль
Forgot password?
CAPTCHA
By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy
Loading data...
Subscribe to our newsletter
specify your contacts

By clicking «#SUBMIT_NAME»,
you agree to our Privacy Policy

You have successfully subscribed
Now you can receive newsletters